Motor Vehicle Inspector • Paper-II
Normally, automotive brakes are
A)
greasy friction
B)
viscous friction
C)
wet friction
D)
dry friction
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'dry friction' (Option D).
Motor Vehicle Inspector • Paper-II
The angular velocities of the two pulleys, connected either by an open belt or a crossed belt are
A)
directly proportional to their diameters
B)
inversely proportional to their diameters
C)
proportional to the square of their diameters
D)
proportional to the square root of their diameters
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'inversely proportional to their diameters' (Option B).
Motor Vehicle Inspector • Paper-II
Natural frequency of a system is due to
A)
free Vibration
B)
forced Vibration
C)
resonance
D)
damping
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'damping' (Option D).
Motor Vehicle Inspector • Paper-II
The device in the distributor that moves the breaker cam ahead as engine speed increases is called the
A)
vacuum advance mechanism
B)
centrifugal – advance mechanism
C)
full – advance mechanism
D)
vacuum – brake mechanism
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'full – advance mechanism' (Option C).
Motor Vehicle Inspector • Paper-II
The brake bleeding process removes from system
A)
air
B)
vacuum
C)
excess fluid
D)
excess pressure
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'excess fluid' (Option C).
Motor Vehicle Inspector • Paper-II
In power steering system, the pump that provides hydraulic pressure operates
A)
intermittently
B)
only when the pressure is needed
C)
continuously
D)
only after one degree turn of the steering wheel
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'intermittently' (Option A).
Motor Vehicle Inspector • Paper-II
The number of points at which the engine – clutch – gearbox unit is supported on the chassis frame is
A)
one
B)
two
C)
three
D)
four
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'two' (Option B).
Motor Vehicle Inspector • Paper-II
The type of rear axle used on truck is
A)
semi floating
B)
fully floating
C)
three quarter floating
D)
none of these
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'three quarter floating' (Option C).
Motor Vehicle Inspector • Paper-II
In frameless chassis
A)
the floor is in tension and the roof is in compression
B)
the floor is in compression and the roof is in tension
C)
both the floor and the roof are in tension
D)
both the floor and the roof are in compression
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'the floor is in tension and the roof is in compression' (Option A).
Motor Vehicle Inspector • Paper-II
Which of the following will normally be not continuous production?
A)
chemical processing
B)
cigarette manufacturing
C)
cement manufacturing
D)
welding shops
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'cement manufacturing' (Option C).
Motor Vehicle Inspector • Paper-II
Most anti-skid devices are employed on
A)
rear brakes
B)
front brakes
C)
secondary brakes
D)
parking brakes
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'secondary brakes' (Option C).
Motor Vehicle Inspector • Paper-II
Automobile chassis is provided with bolted, riveted or welded cross pieces to
A)
give extra weight
B)
give extra strength
C)
tie together the parts
D)
improve the design
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'give extra strength' (Option B).
Motor Vehicle Inspector • Paper-II
Noise when going around a curve indicates the trouble is
A)
due to heavy contact on the heel ends of the bevel gears
B)
due to heavy contact on the toe ends of the bevel gears
C)
in the differential case
D)
due to slippage of the clutch surfaces
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'due to heavy contact on the heel ends of the bevel gears' (Option A).
Motor Vehicle Inspector • Paper-II
In production planning and control systems, which of the following is in the action phase?
A)
order writing
B)
product design
C)
dispatching
D)
data processing
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'dispatching' (Option C).
Motor Vehicle Inspector • Paper-II
The adjustment for backlash in a differential is provided between
A)
crown wheel and the sun gear
B)
sun gear and the planet gear
C)
crown wheel and the drive pinion
D)
crown wheel and the planet gear
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'sun gear and the planet gear' (Option B).
Motor Vehicle Inspector • Paper-II
In a coil spring suspension systems, as the wheel passes over a bump, the shock absorber is
A)
expanded
B)
extended
C)
compressed
D)
none of these
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'none of these' (Option D).
Motor Vehicle Inspector • Paper-II
Rotary motion of the steering wheel is converted to reciprocating motion by
A)
track arm
B)
track rod
C)
stub axle
D)
steering gear box
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'steering gear box' (Option D).
Motor Vehicle Inspector • Paper-II
Which of the following is not a purpose of suspension system?
A)
to safeguard the occupants against road shocks
B)
to provide requisite height to body structure
C)
to adjust cost of the body structure
D)
to keep the body perfectly in level while travelling over uneven ground
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'to provide requisite height to body structure' (Option B).
Motor Vehicle Inspector • Paper-II
The type of gears in which the teeth are parallel to and align with the center of the gear is called
A)
helical gears
B)
bevel gears
C)
worm gears
D)
spur gears
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'helical gears' (Option A).
Motor Vehicle Inspector • Paper-II
The Ignition coil has
A)
one winding
B)
two windings
C)
three windings
D)
four windings
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'two windings' (Option B).
Motor Vehicle Inspector • Paper-II
The alternator produces electricity in its
A)
rotor field
B)
stator windings
C)
regulator
D)
armature commutator
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'regulator' (Option C).
Motor Vehicle Inspector • Paper-II
Three types of springs used in automotive suspension systems are
A)
coil, leaf and torsion bar
B)
coil torsion bar and air
C)
leaf, air and gas
D)
all of these
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'all of these' (Option D).
Motor Vehicle Inspector • Paper-II
In a starter motor the field windings are wound around
A)
armature
B)
commutator
C)
brush
D)
pole shoes
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'brush' (Option C).
Motor Vehicle Inspector • Paper-II
Which of the following will normally be not function of material management?
A)
receiving and ware-housing
B)
standardization
C)
recruitment of staff
D)
inventory control
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'receiving and ware-housing' (Option A).
Motor Vehicle Inspector • Paper-II
With part-time four wheel drive, the transfer –case shift lever must be moved to engage or disengage
A)
the rear differential
B)
the front differential
C)
both front and rear differential together
D)
none of these
Based on established principles in the relevant subject area, the correct and most appropriate choice is 'the rear differential' (Option A).
